REVIEW PG 1/60 DABAN NO.00 GN-001 Gundam Exia, Daban Model

DABAN NO.00  PG 1/60 GN-001 Gundam Exia Review

Daban Model manufacturer has already shipped PG 1/60 Gundam Exia, Daban Model NO.00, it is estimated that many Builder have begun to receive and start to build. Here we go about the Review.

1. Quality

The quality of the board has been explained very clearly in the board drawing. Shrinking, air bubbles, transparent parts are not transparent, and the details are not sharp enough. The white and light gray parts samples are There are some impurities and gray spots. Daban Model said that there will be adjustments. 

However, from the perspective of large goods, there are no obvious improvements and changes. The problem remains. Moreover, due to domestic quality problems, various panels will shrink after large goods. 

Winning prizes and other issues, this is also ironclad. But on the whole, there are really not too many problems after the assembly. Mainly because some shrinkage positions are not visible after the assembly, which weakens the visual experience.

2. Snapfit

The degree of combination is definitely the most relevant question for everyone. Here you can say that the combination of this set of products is really tight, and the whole is tight. A lot of reaming must be done during the combination process. Or cut the pile, otherwise it will be inevitable to vigorously use the diamond finger.It is recommended to handle it well, otherwise the finger will have to be pressed for you.

The advantage of such a compact combination is that even after a full body of equipment, there will be no easy drop-off and other problems, and because it is tight enough, it can still have a lot of problems after installing avalanche equipment. Good joint retention, playing with, standing dead, etc. are all things.

The whole is very tight, so it is not a problem to play (All the actions that can be performed in the article are proof). Even with the avalanche gear, the joints can still be supported without pressure.

3. Head Unit

The face of the head, this time to tell the truth, as far as the face is concerned, it is indeed ok. It is basically restored, and there are no problems with crooked faces, high and low eyes, etc.. It is this manufacturer 60 The ratio is the most positive one, but unfortunately, the biggest problem is that the parts are not sharp enough, and some of the edges are not three-dimensional, so there must be a gap compared with a certain generation, but for domestic production, it’s okay. It can be seen.

4. Led Unit

The lighting of the lamp group is basically normal, and the matched lamp group is basically the same as that of a certain generation. Except for the color of the wire, there is no difference in function. Moreover, from the effect point of view, the luminous and transparent parts guide The light is relatively ideal, and there is no problem of light transmission of the outer armor. Except for the light transmission problem of the upper arm, but only the back of the part needs to be painted black. 

And this time the wires are very strong, and the wires used are relatively thick, so even the use of force during installation will not easily cause damage to the circuit and the wire. (Of course, I said that, but you should pay attention when installing. 

Don't really pull it. After all, there is still a welding position. Of course, this time the light set still has a USB power input. The interface, in other words, can be powered by USB power without a battery, which is quite considerate.

Although there are clear guidelines on the installation and routing methods of the wiring, I still need to mention everyone here, because the interface position of the wiring in some places is just near the combined position of the parts, so be sure to pay attention when hiding the wiring , Try to hide the position of the interface as much as possible, otherwise it is easy to cause problems such as poor combination of parts or poor combination.

5. Weaponry

PG 1/60 Gundam Exia, Daban Model NO.00 Has almost all Gundam Exia modes in the packaging. Starting from Gundam Exia, Gundam Exia Repair 1 and also Avalanche Exia and Avalanche Exia Dash. This completeness allows us to convert PG Gundam Exia into PG Avalanche Exia Gundam or PG Avalanche Exia Dash.

However, GN sword only gave one set, for weapon control, it is indeed insufficient. After all, after installing the machete, you can no longer use the GN sword alone. After all, as a consumer, it is not impossible to equip two more sets of the same board separately. I can only say that I have left a regret when I am satisfied.

In general, this 60-percent avalanche quality is decent, and it is maintained at the domestic medium level (in fact, the manufacturer’s usual level is more appropriate). There are problems, but there are also bright spots. After all, a large proportion of avalanche equipment is indeed Nothing has appeared yet. Of course, many people currently have various opinions and dissatisfaction with the packaging practice, but as a review, they only comment on the product. 

As for topics other than the product, we will not say much. After all, we cannot be biased. Otherwise there will be injustice. It can only be said that as a product itself, things are considered passable, but we cannot say how good it is. It is just a good thing to have multiple choices under the current environment and state. It is just that everyone needs to consider how to choose.

6. Articulation

PG 1/60 Gundam Exia, Daban Model NO.00 has good articulation and is very poseable. There are many poses that can be done by this PG Gundam Exia Daban Model during Gundam Exia mode. Another thing is when using the Avalanche Exia Dash, there are many poses that cannot be done to an extreme, but it should be acknowledged that even in Avalanche Exia Dash mode, this PG Gundam Exia Daban Model still has very good articulation.

 

Related Article